Jump to content


Replacing Hop Up/ Disassembly-Reassembly Video

mp7 replacing hop up replacing disassembly reassembly

  • Please log in to reply
13 replies to this topic

#1 Outlaw1995

Outlaw1995

    Guru

  • Members
  • PipPipPipPip
  • 1,713 posts
  • Gender:Male
  • Interests:Acting, Piano, Films, Theatre, Firearms, Knives, Airsoft
  • Country:

Posted 17 April 2012 - 07:52 PM

Hey guys,
Looking around youtube and the forum and thought sharing these two videos would be beneficial to those who need to take apart their MP7s... Enjoy!





By the way this is not me, I give credit to recall56k, the poster of these two videos.

NOTE: Instead of using a screwdriver like the guy in the video uses, you may use an .89mm or .9mm allen wrench to take out the safety selector screw.

Edited by Outlaw1995, 30 May 2012 - 02:23 PM.


#2 niko_gpsy

niko_gpsy

    What's a Warranty?

  • Super Moderator
  • PipPipPipPip
  • 5,854 posts
  • Gender:Male
  • Location:Atlanta, GA
  • Interests:Keeping those damn squirrels from putting their filthy little paws on my peaches in my backyard. Oh, Yes. It's not just a hobby, its a passion!!
  • Country:

Posted 18 April 2012 - 07:14 AM

Good find.

#3 optimuskmg

optimuskmg

    Enthusiast

  • Members
  • PipPip
  • 293 posts
  • Gender:Male
  • Location:Bridgewater
  • Country:

Posted 18 April 2012 - 12:54 PM

very helpfull. good find

#4 akiraspeedstar

akiraspeedstar

    Guru

  • Members
  • PipPipPipPip
  • 1,130 posts
  • Gender:Male
  • Country:

Posted 18 April 2012 - 05:52 PM

Yeah that's the same video I used to change my hop up bucking.

#5 optimuskmg

optimuskmg

    Enthusiast

  • Members
  • PipPip
  • 293 posts
  • Gender:Male
  • Location:Bridgewater
  • Country:

Posted 20 April 2012 - 07:28 PM

PIN worthy? would like to see this at the top lol used it 4 times allready

#6 Outlaw1995

Outlaw1995

    Guru

  • Members
  • PipPipPipPip
  • 1,713 posts
  • Gender:Male
  • Interests:Acting, Piano, Films, Theatre, Firearms, Knives, Airsoft
  • Country:

Posted 12 May 2012 - 08:19 PM

Just to confirm, I ran through all the instructions tonight to make sure that everything he did was good. I will provide descriptions of the sizes of allen wrenches you will need (in accordance to where they are needed at which times in the video) in order to *PROPERLY* tear your gun down without risk of breaking the screws. And yeah, it'd be awesome if we can get this pinned! ;)

Edited by Outlaw1995, 12 May 2012 - 08:19 PM.


#7 akiraspeedstar

akiraspeedstar

    Guru

  • Members
  • PipPipPipPip
  • 1,130 posts
  • Gender:Male
  • Country:

Posted 12 May 2012 - 11:48 PM

One of the reasons I love GBB is how simple they are to take apart, once you watch a video like this one you say to yourself "that's it?"

Edited by akiraspeedstar, 13 May 2012 - 12:00 AM.


#8 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,301 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 13 May 2012 - 07:36 AM

View PostOutlaw1995, on 12 May 2012 - 08:19 PM, said:

Just to confirm, I ran through all the instructions tonight to make sure that everything he did was good. I will provide descriptions of the sizes of allen wrenches you will need (in accordance to where they are needed at which times in the video) in order to *PROPERLY* tear your gun down without risk of breaking the screws. And yeah, it'd be awesome if we can get this pinned! ;)
Pinned!

#9 kwaispro727

kwaispro727

    Specialist

  • Members
  • PipPipPip
  • 945 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Fishing, swimming, airsoft, real firearms, cars
  • Country:

Posted 16 December 2012 - 09:49 AM

When you take the bolt out, do you just push it back in after? I mean, is there anything to watch out for?

#10 Outlaw1995

Outlaw1995

    Guru

  • Members
  • PipPipPipPip
  • 1,713 posts
  • Gender:Male
  • Interests:Acting, Piano, Films, Theatre, Firearms, Knives, Airsoft
  • Country:

Posted 16 December 2012 - 12:12 PM

View Postkwaispro727, on 16 December 2012 - 09:49 AM, said:

When you take the bolt out, do you just push it back in after? I mean, is there anything to watch out for?
No there isn't anything really to watch out for besides lining the bolt up with the grooves it is supposed to slide on. What I like to do is take the bolt assembly, attach it to the recoil spring guide and hold it in place by the charging handle, and just put the whole thing (including the rear plate) into the frame of the gun, keeping my index finger on the charging handle keeping the bolt lined up and secure. I find that easiest, and it gets everything back in together without having to worry about if things somehow got messed up.

#11 Icurblud

Icurblud

    Enthusiast

  • Members
  • PipPip
  • 95 posts
  • Gender:Male
  • Location:Pennsylvania
  • Country:

Posted 10 January 2013 - 08:36 PM

very good information.

#12 Kurama

Kurama

    Newbie

  • Members
  • Pip
  • 6 posts
  • Country:

Posted 06 February 2013 - 08:45 PM

One thing that might annoy people, is getting the trigger back in. If at any point, your trigger might get stuck and the spring hold it back too far where you cant move it out again, use something small to push the spring back forwards into the opening and remove the trigger again.

#13 kwaispro727

kwaispro727

    Specialist

  • Members
  • PipPipPip
  • 945 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Fishing, swimming, airsoft, real firearms, cars
  • Country:

Posted 21 March 2013 - 06:38 PM

I just took mine apart and after watching this video I see him struggling  a little to get the piece that pushes up and down on the nub back in.  Why not simply put that piece in before pushing the rest of the assembly with the inner barrel back together?

#14 Outlaw1995

Outlaw1995

    Guru

  • Members
  • PipPipPipPip
  • 1,713 posts
  • Gender:Male
  • Interests:Acting, Piano, Films, Theatre, Firearms, Knives, Airsoft
  • Country:

Posted 23 March 2013 - 07:23 AM

View Postkwaispro727, on 21 March 2013 - 06:38 PM, said:

Why not simply put that piece in before pushing the rest of the assembly with the inner barrel back together?
The order in which the gun is assembled may be crucial in terms of how the gun will function. I wouldn't recommend reassembling any other way.





Also tagged with one or more of these keywords: mp7, replacing hop up, replacing, disassembly, reassembly

0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users