Jump to content


Kmp9 Tear Down Guide


  • Please log in to reply
49 replies to this topic

#21 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,565 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 18 July 2011 - 12:19 PM

Do you mean take down pin # 34?

#22 dattguyy

dattguyy

    Newbie

  • Members
  • Pip
  • 28 posts
  • Gender:Male
  • Location:Illinois
  • Interests:Airsoft
    Baseball
    PS3
  • Country:

Posted 18 July 2011 - 02:28 PM

Yes the take down pin #34

#23 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,565 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 18 July 2011 - 04:45 PM

Read my post here: http://www.kwausa.co...h=1
  And look at the bolt installation video on the DIY thread: http://www.kwausa.co...?showtopic=6022

Hope this helps.

#24 dattguyy

dattguyy

    Newbie

  • Members
  • Pip
  • 28 posts
  • Gender:Male
  • Location:Illinois
  • Interests:Airsoft
    Baseball
    PS3
  • Country:

Posted 01 August 2011 - 11:50 AM

Yeah for some reason my take-down clamp, part #63, is locked in place and doesn't move.  And I believe it is because of that, that I can't pull out the take-down pin.  Is there any way to fix this?

#25 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,565 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 01 August 2011 - 02:54 PM

First make sure you have not lifted the assembly up. Next push Part #63 to the rear slightly, it should move.  Then you can lift up the pin.

Here's a vid that may help: http://kwausa.com/co...low-power-bolt/

#26 dattguyy

dattguyy

    Newbie

  • Members
  • Pip
  • 28 posts
  • Gender:Male
  • Location:Illinois
  • Interests:Airsoft
    Baseball
    PS3
  • Country:

Posted 02 August 2011 - 04:42 PM

Thanks for the help, I got the take-down pin out.  I think I just had to keep the assembly pushed down while I did it.  Unfortunately when I was pulled the pin out with my pliers, the end of the handle came up and knocked me the forehead.  Now I've got a nice lump on my face.  Anyway, I'm just glad to finally take my KMP9 apart.

#27 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,565 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 02 August 2011 - 06:10 PM

I thought you where going to say you broke something on the gun!!! Your face will heal.  Just kidding, sorry you got hurt and glad we could help. :gun:

#28 Outlaw1995

Outlaw1995

    Guru

  • Members
  • PipPipPipPip
  • 1,713 posts
  • Gender:Male
  • Interests:Acting, Piano, Films, Theatre, Firearms, Knives, Airsoft
  • Country:

Posted 31 January 2012 - 04:00 PM

Hey dobey!! Nice instructional tutorial. How were you able to put the images straight to the post?

#29 niko_gpsy

niko_gpsy

    What's a Warranty?

  • Super Moderator
  • PipPipPipPip
  • 5,878 posts
  • Gender:Male
  • Location:Atlanta, GA
  • Interests:Keeping those damn squirrels from putting their filthy little paws on my peaches in my backyard. Oh, Yes. It's not just a hobby, its a passion!!
  • Country:

Posted 31 January 2012 - 08:58 PM

View PostOutlaw1995, on 31 January 2012 - 04:00 PM, said:

Hey dobey!! Nice instructional tutorial. How were you able to put the images straight to the post?

Photobucket? Or similar sites............

#30 Animaniacfromhi

Animaniacfromhi

    Newbie

  • Members
  • Pip
  • 4 posts
  • Country:

Posted 31 January 2012 - 10:45 PM

Hi Dobey, is there any instructions to tear down to the Recoil Buffer Plate? I need to reattach it back b/c the Recoil Buffer Screws Part# 104 screws came off so the recoil plate came off. However, I have to disassemble the whole back gun to get access to the screws. Thanks.

#31 dobey

dobey

    Enthusiast

  • Members
  • PipPip
  • 234 posts
  • Gender:Male
  • Location:NY
  • Country:

Posted 14 February 2012 - 05:05 AM

I have had the metal hammer assembly out of my gun 1 time to repair a broken pin, and it was dicey.  You have to spread the plastic body at the sides to get the assembly out because of the fake pins that hold it in.  You need to be very carefull doing this or you will break the plastic!

#32 Animaniacfromhi

Animaniacfromhi

    Newbie

  • Members
  • Pip
  • 4 posts
  • Country:

Posted 15 February 2012 - 11:35 AM

So in picture 007, I have to stretch out the KMP9's plastic sides to get the back part out?

#33 vilerk

vilerk

    Newbie

  • Members
  • Pip
  • 15 posts

Posted 17 February 2012 - 12:09 AM

For mine, I didn't have to spread the plastic.  There are two set screws on each side of the valve knocker assembly that hold the 2 pins in.  After you unscrew those, you can pry out the pins from the inside.

#34 apacifico3

apacifico3

    Enthusiast

  • Members
  • PipPip
  • 206 posts
  • Gender:Male
  • Location:Georgia, US, Earth
  • Interests:Soccer, Airsoft, Sports
  • Country:

Posted 25 February 2012 - 05:59 PM

I had to spread the plastic. My disconnector bar (#153) snapped after about 10,000 rounds, so tinkered around with the trigger/hammer mechanism and realized you had to pull the plastic away and slide the metal group out. Time to wash, rinse, replace, and put back together.

#35 apacifico3

apacifico3

    Enthusiast

  • Members
  • PipPip
  • 206 posts
  • Gender:Male
  • Location:Georgia, US, Earth
  • Interests:Soccer, Airsoft, Sports
  • Country:

Posted 25 February 2012 - 07:50 PM

Posting pics of the broken parts. Might make a full guide of a complete tear down.

Disconnector bar snapped, purchased another on the pro shop.
Posted Image

All the lower internal parts removed, washed, and dried.
Posted Image

New bolt catch installed in loading ramp mechanism. Old one is pictured below the ramp assembly. The old one was too rounded and did not lock the bolt when the mag was empty.
Posted Image

Oh KMP9... What a piece of work you are.

#36 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,565 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 25 February 2012 - 07:54 PM

Just curious, did you buy your MP9 new?

#37 apacifico3

apacifico3

    Enthusiast

  • Members
  • PipPip
  • 206 posts
  • Gender:Male
  • Location:Georgia, US, Earth
  • Interests:Soccer, Airsoft, Sports
  • Country:

Posted 25 February 2012 - 08:20 PM

Yup, brand new a while back off Evike when they had a nice coupon code. Why do you ask?

#38 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,565 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 25 February 2012 - 08:23 PM

Because that old bolt catch has been modified.  The rounded corners gives it away.

#39 apacifico3

apacifico3

    Enthusiast

  • Members
  • PipPip
  • 206 posts
  • Gender:Male
  • Location:Georgia, US, Earth
  • Interests:Soccer, Airsoft, Sports
  • Country:

Posted 25 February 2012 - 08:31 PM

I had it sent in to KWA when I first got it because the bolt wouldn't lock. That's what it came back like (although I did continue to use it and probably wore it down a bit more).

#40 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,565 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 25 February 2012 - 08:33 PM

That would be it then.  Thanks.




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users