Jump to content


Battery with Deans (Will it fit?)


  • Please log in to reply
15 replies to this topic

#1 alexsteele

alexsteele

    Newbie

  • Members
  • Pip
  • 9 posts
  • Country:

Posted 20 July 2014 - 06:15 PM

Hey KWAers. I want to get this battery as my gun is wired for deans and this one already has it attached. Will it fit in the stock?

http://www.amazon.co...QJAK2CCPY8G12TH

If not, can someone link me to a 11.1 lipo 2000+mah with deans that would fit? I have a MOSFET and know KWA recommends 15C or below, consider me warned!

Thanks :)

#2 StealthTaskForce

StealthTaskForce

    Enthusiast

  • Members
  • PipPip
  • 228 posts
  • Gender:Male
  • Location:Tampa
  • Interests:Airsoft, Paintball, Sports, My girlfriend, Knives and Real Steel
  • Country:

Posted 20 July 2014 - 07:59 PM

Fit in the stock of what? Worse comes to worse, measure the damn thing. Use the measurements from the website given, and then measure your stock and see if it will fit.

#3 tales

tales

    Specialist

  • Members
  • PipPipPip
  • 547 posts
  • Gender:Male
  • Location:Brooklyn NY
  • Interests:Fishing, RC cars, Building Motion Picture sets
  • Country:

Posted 20 July 2014 - 08:20 PM

In the Butt Plate? the battery in the link might be too big. i think the butt plate battery is 100 X 31 X 17

This fits if you remove the fuse harness in the buffer tube
http://www.ebay.com/...vectorid=229466

And the batteries in the pro shop. You will have to change the connectors.

#4 tales

tales

    Specialist

  • Members
  • PipPipPip
  • 547 posts
  • Gender:Male
  • Location:Brooklyn NY
  • Interests:Fishing, RC cars, Building Motion Picture sets
  • Country:

Posted 20 July 2014 - 08:23 PM

 StealthTaskForce, on 20 July 2014 - 07:59 PM, said:

Fit in the stock of what? Worse comes to worse, measure the damn thing. Use the measurements from the website given, and then measure your stock and see if it will fit.

Ouch!

#5 StealthTaskForce

StealthTaskForce

    Enthusiast

  • Members
  • PipPip
  • 228 posts
  • Gender:Male
  • Location:Tampa
  • Interests:Airsoft, Paintball, Sports, My girlfriend, Knives and Real Steel
  • Country:

Posted 20 July 2014 - 08:26 PM

Ouch what? I've done it haha I just need to rewire to the back, and I know of a battery that SHOULD fit. Should being the operative word though lol

#6 tales

tales

    Specialist

  • Members
  • PipPipPip
  • 547 posts
  • Gender:Male
  • Location:Brooklyn NY
  • Interests:Fishing, RC cars, Building Motion Picture sets
  • Country:

Posted 20 July 2014 - 08:57 PM

"That should fit", post it for the OP.  Not every battery fits in the butt plate.

"haha" remember when you started posting and i offered to help you with motors.Can you be a little nicer and do the same for others.

If you need advice rewiring your MOD2 to the rear, i won't tell you Measure the dam thing. Ill try and help.

I also rewired a MOD2 & would answer questions, we try to help each other here :)
Posted Image

Goodnight STF

#7 StealthTaskForce

StealthTaskForce

    Enthusiast

  • Members
  • PipPip
  • 228 posts
  • Gender:Male
  • Location:Tampa
  • Interests:Airsoft, Paintball, Sports, My girlfriend, Knives and Real Steel
  • Country:

Posted 20 July 2014 - 09:30 PM

I apologize if I came off as being hostile or mean.. I didn't mean to. I didn't know what gun he needed it to fit in, so that's why I said worse comes to worse, measure it. You can't really go wrong with measuring it if you know how much space the wiring should take up in the buffer tube, if that's where he plans to put it. The reason I asked what gun, is because I have a regular crane stock on mine and can't put batteries anywhere other than in the buffer tube which is why he should measure it. Again I apologize if I came off as mean or rude. I didn't mean to.


Sent from my iPhone using Tapatalk

#8 tales

tales

    Specialist

  • Members
  • PipPipPip
  • 547 posts
  • Gender:Male
  • Location:Brooklyn NY
  • Interests:Fishing, RC cars, Building Motion Picture sets
  • Country:

Posted 20 July 2014 - 09:43 PM

NP it happens you came a long way, i know you're not a rude person. I enjoy your posts.

Batteries fit in three places on a KWA stock: battery compartment X2, one in buffer tube if fuse harness is removed & a brick in the butt plate the battery he posted won't fit anywhere


Internet pic BATT in KWA Butt Plate
Posted Image

These will fit in the battery compartment one cell in each & one in the buffer tube, on a crane stock. but you have tho remove the fuse harness to get the center cell in.
Posted Image

Edited by tales, 20 July 2014 - 09:58 PM.


#9 Pyro_Buster

Pyro_Buster

    Enthusiast

  • Members
  • PipPip
  • 134 posts
  • Gender:Male
  • Location:California
  • Country:

Posted 20 July 2014 - 10:51 PM

This battery is built specifically for KWA's. http://www.eliteairs...unchuck-2n.aspx

#10 Chuck S

Chuck S

    Guru

  • Members
  • PipPipPipPip
  • 1,315 posts
  • Gender:Male
  • Location:Cleveland, Ohio
  • Country:

Posted 21 July 2014 - 02:33 AM

$45 is a lot of money for an AEG battery.  My AEGs are wired under the handguards and the original battery listed above is too big in every demension.  The best I've found there is
Posted Image
but you have to wire your own Deans connection.  I believe this also fits the KWA crane stock and is/was sold by KWA in the Pro Shop.

-- Chuck

#11 alexsteele

alexsteele

    Newbie

  • Members
  • Pip
  • 9 posts
  • Country:

Posted 21 July 2014 - 02:35 AM

Thank you all. This is for the SR10. I did the measuring for the butt plate and was having issues finding batteries that would fit without sacrificing power and was wondering what batteries the KWA community used specifically as I'm sure I'm not the first to run into this. That said. These suggestions help!

#12 alexsteele

alexsteele

    Newbie

  • Members
  • Pip
  • 9 posts
  • Country:

Posted 21 July 2014 - 02:37 AM

 tales, on 20 July 2014 - 09:43 PM, said:

NP it happens you came a long way, i know you're not a rude person. I enjoy your posts.

Batteries fit in three places on a KWA stock: battery compartment X2, one in buffer tube if fuse harness is removed & a brick in the butt plate the battery he posted won't fit anywhere


Internet pic BATT in KWA Butt Plate
Posted Image

These will fit in the battery compartment one cell in each & one in the buffer tube, on a crane stock. but you have tho remove the fuse harness to get the center cell in.
Posted Image

Takes can you link me to these?

#13 alexsteele

alexsteele

    Newbie

  • Members
  • Pip
  • 9 posts
  • Country:

Posted 21 July 2014 - 02:38 AM

 Chuck S, on 21 July 2014 - 02:33 AM, said:

$45 is a lot of money for an AEG battery.  My AEGs are wired under the handguards and the original battery listed above is too big in every demension.  The best I've found there is
Posted Image
but you have to wire your own Deans connection.  I believe this also fits the KWA crane stock and is/was sold by KWA in the Pro Shop.

-- Chuck

Chuck what's the link for this? :)

 tales, on 20 July 2014 - 09:43 PM, said:

NP it happens you came a long way, i know you're not a rude person. I enjoy your posts.

Batteries fit in three places on a KWA stock: battery compartment X2, one in buffer tube if fuse harness is removed & a brick in the butt plate the battery he posted won't fit anywhere


Internet pic BATT in KWA Butt Plate
Posted Image

These will fit in the battery compartment one cell in each & one in the buffer tube, on a crane stock. but you have tho remove the fuse harness to get the center cell in.
Posted Image


#14 tales

tales

    Specialist

  • Members
  • PipPipPip
  • 547 posts
  • Gender:Male
  • Location:Brooklyn NY
  • Interests:Fishing, RC cars, Building Motion Picture sets
  • Country:

Posted 21 July 2014 - 05:08 AM

There were sold by HobbyKing. I haven't seen them listed for months. The only place i can find them is ebay.

New
http://www.ebay.com/...202065803&rt=nc

Used Once?
http://www.ebay.com/...=p2054897.l4275

there are other batteries that fit in the butt plate, i don't have any links.
With the BP battery you only need to rewire the connector, not the fuse harness.

#15 hellcat

hellcat

    Enthusiast

  • Members
  • PipPip
  • 132 posts
  • Gender:Male
  • Location:west palm beach florida
  • Interests:Airsoft, Football, Nascar, Guns, cars/trucks, and of women in yoga pants!!
  • Country:

Posted 21 July 2014 - 02:25 PM

this fits in the butt plate perfect.    http://www.hobbypart...hort-asoft.html

#16 Chuck S

Chuck S

    Guru

  • Members
  • PipPipPipPip
  • 1,315 posts
  • Gender:Male
  • Location:Cleveland, Ohio
  • Country:

Posted 21 July 2014 - 02:41 PM

This is a link to the battery I'm using.  Dimensions: 90mm x 28mm x 11mm.  

This video says the BOL brick style (pictured above in my post) will work in all KWA AEGS.  Jump ahead to mark 3:30 for what fits.  (You can watch Veronica on your own time!)

I use this battery in my KM4-CQB and RM4.

If you want Deans get your soldering iron out!  ;)

-- Chuck




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users