Jump to content


Some thoughts on the new PTS Mega Arms MKM


  • Please log in to reply
186 replies to this topic

#161 PonZee

PonZee

    Newbie

  • Members
  • Pip
  • 17 posts
  • Gender:Male
  • Location:North Carolina
  • Country:

Posted 07 July 2014 - 06:45 PM

Has there been any word on the Masada GBB that was shown during Shot Show? Or has it been scrapped? I'd like to know if I can eventually throw my EVOII hop-up set into that considering it supposedly would be using the LM4 hop-up.

#162 uscmCorps

uscmCorps

    Magpul PTS

  • Members
  • PipPip
  • 155 posts
  • Gender:Male
  • Location:SoCal
  • Country:

Posted 08 July 2014 - 02:21 AM

The Masada GBBR has not been scrapped. However out of respect to KWA's requests, since the Masada is not a KWA specific product (neither is the MKM for that matter) I won't be discussing another company's product on their KWA company forum. When there's new info to share, it will be shared in the appropriate public forum/venue. We are fortunate that KWA has allowed the continued usage of this thread regarding the MKM on their forum. Let's keep the discussion on topic please. ;)

#163 PonZee

PonZee

    Newbie

  • Members
  • Pip
  • 17 posts
  • Gender:Male
  • Location:North Carolina
  • Country:

Posted 08 July 2014 - 04:26 AM

Oh, my fault. Some YouTube videos labeled it as a KWA product. Thanks for the info, though!

#164 BeachEMT

BeachEMT

    Specialist

  • Members
  • PipPipPip
  • 534 posts
  • Gender:Male
  • Location:People's Republic of California
  • Interests:Engineering, Emergency Medicine
  • Country:

Posted 11 July 2014 - 03:51 PM

Hey Boobie, I'm still a little curious about the inconsistent dimensions between the MKM and LM4 uppers. Obviously the tabs are geometrically different, but what about other dimensions like pin spacing and the curvature near the buffer tube? If a receiver were able to accommodate both types of tabs, would both receivers be compatible? Also, would you mind posting the dimensions of the MKM tabs, please?

Edit: Can anyone confirm whether or not the MKM buffer lock is the same as the LM4? I'm wondering if I should get an extra BBA steel lock while I'm ordering one for my Magpul.

Edited by BeachEMT, 14 July 2014 - 09:58 PM.


#165 crowley

crowley

    Enthusiast

  • Members
  • PipPip
  • 104 posts
  • Country:

Posted 16 July 2014 - 09:55 PM

Hi

Yep, Buffer Stop is 100% the same.
I replaced mine with the BBA Steel Buffer Stop, perfect fit

#166 BeachEMT

BeachEMT

    Specialist

  • Members
  • PipPipPip
  • 534 posts
  • Gender:Male
  • Location:People's Republic of California
  • Interests:Engineering, Emergency Medicine
  • Country:

Posted 17 July 2014 - 07:26 AM

Thank you crowley! Anyone know about hole spacing or anything else that might affect receiver inter-compatibility, besides the tabs?

#167 BeachEMT

BeachEMT

    Specialist

  • Members
  • PipPipPip
  • 534 posts
  • Gender:Male
  • Location:People's Republic of California
  • Interests:Engineering, Emergency Medicine
  • Country:

Posted 17 July 2014 - 08:29 AM

*sorry for the double post*

Edited by BeachEMT, 17 July 2014 - 08:30 AM.


#168 phatkid51

phatkid51

    Newbie

  • Members
  • Pip
  • 1 posts
  • Country:

Posted 22 July 2014 - 03:15 PM

Hey Guys just got MY Mega Arms MKM yesterday and I'm wondering if the RA tech NPAS for the standard LM4 will work in my MKM...I'd like to use it for CBQ on the odd occasion...or even the RA Tech BCG? thanks in advance!

#169 archangel

archangel

    Newbie

  • Members
  • Pip
  • 11 posts

Posted 25 July 2014 - 11:55 PM

Anyone else use the LM4 Pmags with the MKM?

I bought 6 as I prefer the look of these to the standard mags, but keep having problems with these locking the bolt back, even with a full mag.

After comparing these space between the top of the mag and the bolt stop lever, the standard mag has a shorter stop lever than the pmags. From measurements, there seems to be about 0.7mm difference.

So in theory, if this gap is enlarged on the Pmags, they should work as well as the standard mags. Has anyone tried this before or at lleast know if this seems a sensible thing to do! I would rather mod the mags, and keep compatibility with standard mags.

There are also quite a few videos on modding the bolt catch on the LM4, what does this fix on the LM4?

#170 crowley

crowley

    Enthusiast

  • Members
  • PipPip
  • 104 posts
  • Country:

Posted 27 July 2014 - 12:18 AM

Hi

We found a simple and effective Fix to get the PMAGs running stable in the MKM

The PMAG (so also the Disconnector) sits a tiny bit higher in the MKM as the the STANAG Magazine!
So the Magazine Disconnector Part No 16 pushes the Bolt Catch up too soon after every Shot and not when the Magazine is empty

See Magazine Part No 16 Disconnector here:
http://www.kwausa.co..._lm4pts_mag.jpg

So simply shorten the Disconnector 0,6mm where it meets the Bolt Catch, now your PMAG will work perfectly fine, Bolt Catch hits after last Round as it should

To disassemble the PMAG Shell unscrew the Bottomscrews 25,26 and push the Magazine out of the Shell
Then take out the Disconnector No 16 and file down the small square Top with a File or Sandpaper

Also the PMAG fits a little bit more loose in the Magwell, but that is no Problem over all, i ve seen Real Steel Lowers with looser fit ;)

PS
Sorry, my English is very bad

Edited by crowley, 27 July 2014 - 09:10 AM.


#171 lockout

lockout

    Newbie

  • Members
  • Pip
  • 4 posts
  • Country:

Posted 18 August 2014 - 11:13 PM

Hey Folks,
So quick question ,Out of the Box, bone stock MKM with .30 Bioval is still overhopping close to the end of the trajectory and this is all happening with Zero hop engaged. Is it just my MKM or do all MKM's do this....
Regards.

Edited by lockout, 18 August 2014 - 11:14 PM.


#172 scubasteve

scubasteve

    Newbie

  • Members
  • Pip
  • 1 posts
  • Country:

Posted 19 August 2014 - 04:35 AM

Mine does not. Out of the box, I maxed the hop up dial and it is almost perfect for Madbull .36g bbs.

#173 BoobieM4H

BoobieM4H

    Guru

  • Members
  • PipPipPipPip
  • 1,069 posts
  • Gender:Male
  • Location:SAN JOSE, CA
  • Interests:IF IT USES GREEN GAS..I MAKE IT SHOOT BETTER!
  • Country:

Posted 21 August 2014 - 05:35 PM

Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted ImagePosted Image

#174 uscmCorps

uscmCorps

    Magpul PTS

  • Members
  • PipPip
  • 155 posts
  • Gender:Male
  • Location:SoCal
  • Country:

Posted 21 August 2014 - 05:47 PM

Man, that came out awesome! Burnt Bronze Cerakote?

#175 crowley

crowley

    Enthusiast

  • Members
  • PipPip
  • 104 posts
  • Country:

Posted 22 August 2014 - 04:13 AM

As we can see on PTS Facebook Page, the BAD Ambi Safety Selector is ready for WA and KWA LM4 !
Posted Image

uscmcorps, do you know whats up with the MKM Version ?

Edited by crowley, 22 August 2014 - 04:14 AM.


#176 uscmCorps

uscmCorps

    Magpul PTS

  • Members
  • PipPip
  • 155 posts
  • Gender:Male
  • Location:SoCal
  • Country:

Posted 22 August 2014 - 08:41 AM

I'm trying to get an update on this also.

#177 gcw360

gcw360

    Supreme Guru

  • Super Moderator
  • PipPipPipPip
  • 11,665 posts
  • Gender:Male
  • Location:New Jersey
  • Interests:Airsoft (Especially repair and customizing), Fly Fishing, Fossils (Especially Dino), Snakes, Photography
  • Country:

Posted 22 August 2014 - 12:02 PM

View PostBoobieM4H, on 21 August 2014 - 05:35 PM, said:

Posted Image
Posted Image
Posted Image
Posted Image
Posted Image
Posted ImagePosted Image
Mighty fine!

#178 uscmCorps

uscmCorps

    Magpul PTS

  • Members
  • PipPip
  • 155 posts
  • Gender:Male
  • Location:SoCal
  • Country:

Posted 22 August 2014 - 12:11 PM

View Postcrowley, on 22 August 2014 - 04:13 AM, said:

As we can see on PTS Facebook Page, the BAD Ambi Safety Selector is ready for WA and KWA LM4 !

uscmcorps, do you know whats up with the MKM Version ?

Update, two versions of the BAD Selector for GBBRs are available:
BAD Selector set for the KWA LM4, PTS Magpul LM4, KSC M4
BAD Selector set for the MKM, WA M4, G&P M4

I believe both will be available in Black or FDE and include 5 different levers.

#179 Elx3248

Elx3248

    Enthusiast

  • Members
  • PipPip
  • 32 posts
  • Gender:Male
  • Location:Orange County, CA
  • Country:

Posted 22 August 2014 - 01:48 PM

any idea of when they'll make it to the states?

#180 crowley

crowley

    Enthusiast

  • Members
  • PipPip
  • 104 posts
  • Country:

Posted 22 August 2014 - 08:50 PM

Uscmcorps, Are you sure? The WA Version fits into the Mega Arms?
The Detent Pin Location is different etc...how can it fit?

Edited by crowley, 22 August 2014 - 08:53 PM.





1 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users


    Yahoo (1)