Service Advisory - Loose motor terminal connectors
Posted 21 April 2010 - 01:09 PM
Posted 21 April 2010 - 04:33 PM
song is K-ON "DONT SAY LAZY"
Posted 21 April 2010 - 05:51 PM
Posted 21 April 2010 - 09:02 PM
Posted 14 December 2010 - 04:55 PM
my sr-10 wouldnt shoot every once in a while and then stopped shooting completely as id no battery was connected. I krimped the terminals just like the video and it works like new now. At first I krimped them too tight so be careful it was a pain to unkrimp it a litrle.. just try taking them off and putting them back on first and if that doesnt work try to slightly krimp them. Good video.
Posted 15 February 2011 - 12:59 PM
Posted 16 February 2011 - 10:41 AM
NOTE I have four different kWa M4 and this one has that only problem. All the others have serve their master faithfully
Edited by tagajolo, 16 February 2011 - 10:43 AM.
Posted 16 February 2011 - 01:21 PM
Posted 16 February 2011 - 03:08 PM
I forgot to tell you guys it dosen't shoot at semi....only at full auto...
Edited by tagajolo, 16 February 2011 - 03:24 PM.
Posted 25 February 2011 - 11:18 AM
Posted 31 May 2011 - 12:38 AM
With battery connected and with the motor out of the hand grip, I pressed the trigger and held the motor, then rotated the gear with my fingers until I felt the motor wanted to start. (YES! It IS dangerous doing this! I do NOT suggest anyone doing this! I just happen to be experienced in doing this type of work.....) I turned the pinion gear a slight turn, then pressed the trigger. The motor turned. Release the trigger, motor stopped. Pressed trigger again, motor did not turn.
So I examined the motor carefully while doing various test, and I did see that the plates was off on one side. So I loosen the screw, moved the plate until it was flushed together with my thumbnail. Tighten screw, and tested the motor a few times by pressing and releasing the trigger. This time, the motor turned always.
So, the problem was a loose screw on the motor itself! I always believe "Made in Taiwan" was way better than "Made in China". But this was a major setback to me personal belief!
Posted 05 August 2011 - 02:59 PM
Hi, My name is Austin and I am new to the forums. I have always dreaded taking the base plate off of my pistol grip because I hate adjusting motor height. For some reason I can never seem to get it right. I have one simple question. Assuming that my motor height is perfect, if I was to take off the base plate and not turn the set screw at all, would the motor height be the same after reinstalling the base plate? Or would it need adjusting.
Btw sorry for replying to an ancient post.
Edited by Airforceguy664, 05 August 2011 - 03:00 PM.
Posted 05 August 2011 - 05:42 PM
Hope this helps.
Posted 06 August 2011 - 02:38 PM
Hope this helps.
Awesome. Thanks for the help.
Posted 24 February 2013 - 09:29 PM
Hello, So after having my gun stop working after I removed and put back on the base plate, I stumbled upon this video and I have one thing to say.... I lost that gold disk between the motor and screw you were talking about so is that why my gun has stopped working, if so where can I get another I cant seem to find it anywhere!
Posted 25 February 2013 - 04:13 AM
If you have purchased your KWA KM4 in the last year and it has a brass motor height adjustment screw it will not come with a motor base plate disk. And even if it did and you have lost it, the disk is not a critical part that will cause your gun to stop firing. All it will need would be to readjust the motor height for optimal performance.
When did you purchase your KWA KM4 and does it have the brass adjustment screw on the base plate?
Posted 25 February 2013 - 06:39 PM
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users