Jump to content


Madbull and Systema Tightbores


  • Please log in to reply
30 replies to this topic

#21 Guest_allizard_*

Guest_allizard_*
  • Guests

Posted 08 September 2008 - 03:20 PM

I don't think anyone make 6mm bb's that's actually bigger than 6mm.

#22 brooklyn468

brooklyn468

    Specialist

  • Members
  • PipPipPip
  • 559 posts

Posted 08 September 2008 - 04:07 PM

View PostShmoogly3, on Sep 8 2008, 04:21 PM, said:

I would like to note that you said average. That means on average most bbs will measur just under 6mm, but what about the other bbs that could measure just over 6mm (say 6.02 or so) that would mean that your getting friction which would slow your bbs velocity and would definitly drop your accuracy and would fail as a tight bore. If your buying a bag of 5000bbs your definitly going to have bbs in that bag that are alittle off measurment and with an aeg shooting full auto, some of those falty bbs are going to run through your barrel. If you go up to a 6.03mm you will definitly decrease the chances of faulty bbs. Coming to my conclusion, getting a 6.00mm tight bore is almost pointless for an aeg unless for shooting semi auto (sniper), it totally defeats the purpose of a tight bore barrel for and aeg. DON'T GET A 6.00MM TIGHT BORE FOR AND AEG THAT YOU SHOOT FULLY AUTOMATIC WITH!!!!!

There are no such things as airsoft snipers.

Anyway, that may be the case, but with higher quality bbs, like KSC Perfect ( I use AE ), I would doubt that would happen.

#23 DaTigah

DaTigah

    Enthusiast

  • Members
  • PipPip
  • 86 posts
  • Location:East Stroudsburg, PA United States

Posted 08 September 2008 - 05:30 PM

So according to the previous comments, a Prometheus 363mm Tight Bore is perfectly compatible with the Stock Bucking and the Stock Plastic Hop Up Unit?

Just needed to clear somethings.

#24 hammer

hammer

    Enthusiast

  • Members
  • PipPip
  • 85 posts
  • Location:Pi

Posted 08 September 2008 - 06:49 PM

View PostDaTigah, on Sep 8 2008, 05:30 PM, said:

So according to the previous comments, a Prometheus 363mm Tight Bore is perfectly compatible with the Stock Bucking and the Stock Plastic Hop Up Unit?

Just needed to clear somethings.

Yes.

#25 Shmoogly3

Shmoogly3

    Enthusiast

  • Members
  • PipPip
  • 149 posts
  • Gender:Male
  • Location:Wisconsin
  • Interests:Outdoor inthusiest
    Airsofting
    Martial arts
    Cycling
    Hiking
  • Country:

Posted 08 September 2008 - 07:10 PM

I never said that a prometheus wasn't compatible with the stock bucking. I was talking about using a 6mm tight bore. You will have some bbs in the batch that are alittle over 6mm and under 6mm. It is more rare that the bbs go over 6mm, but they do. Nothings truely perfect.

Edited by Shmoogly3, 08 September 2008 - 07:11 PM.


#26 brooklyn468

brooklyn468

    Specialist

  • Members
  • PipPipPip
  • 559 posts

Posted 10 September 2008 - 05:28 PM

View PostShmoogly3, on Sep 8 2008, 10:10 PM, said:

I never said that a prometheus wasn't compatible with the stock bucking. I was talking about using a 6mm tight bore. You will have some bbs in the batch that are alittle over 6mm and under 6mm. It is more rare that the bbs go over 6mm, but they do. Nothings truely perfect.

I'm sure some do, but I thought they did a quality check on high polished bbs. (KSC, AE)

#27 Shmoogly3

Shmoogly3

    Enthusiast

  • Members
  • PipPip
  • 149 posts
  • Gender:Male
  • Location:Wisconsin
  • Interests:Outdoor inthusiest
    Airsofting
    Martial arts
    Cycling
    Hiking
  • Country:

Posted 11 September 2008 - 12:43 PM

They do, but do you think there going to take each bb look at it and measure them, even the machines can't catch every single bb and make sure it's perfectly 6mm. If they had the time to look at every bb the bb's wouldn't be able to be mass produced.

#28 karMeister

karMeister

    Guru

  • Members
  • PipPipPipPip
  • 1,534 posts
  • Gender:Male
  • Location:a small hole under a rock =P
  • Interests:EAR=((1+APR/n)^n)-1
  • Country:

Posted 11 September 2008 - 01:27 PM

Last time I checked there were no BBs above 5.98mm.  Most measured around 5.93

Posted Image  this photo belongs to shredder

Edited by karMeister, 11 September 2008 - 01:32 PM.


#29 Shmoogly3

Shmoogly3

    Enthusiast

  • Members
  • PipPip
  • 149 posts
  • Gender:Male
  • Location:Wisconsin
  • Interests:Outdoor inthusiest
    Airsofting
    Martial arts
    Cycling
    Hiking
  • Country:

Posted 11 September 2008 - 04:26 PM

Oh my god alright whatever I'm done arguing about the stupid bbs my discussions ended with this thread.

#30 brooklyn468

brooklyn468

    Specialist

  • Members
  • PipPipPip
  • 559 posts

Posted 11 September 2008 - 04:27 PM

View PostkarMeister, on Sep 11 2008, 04:27 PM, said:

Last time I checked there were no BBs above 5.98mm.  Most measured around 5.93

Posted Image  this photo belongs to shredder

Exactly! Thanks for the pic, Shredder  :)

#31 karMeister

karMeister

    Guru

  • Members
  • PipPipPipPip
  • 1,534 posts
  • Gender:Male
  • Location:a small hole under a rock =P
  • Interests:EAR=((1+APR/n)^n)-1
  • Country:

Posted 11 September 2008 - 07:44 PM

View Postbrooklyn468, on Sep 11 2008, 04:27 PM, said:

Exactly! Thanks for the pic, Shredder  :)

For the record Im currently using a 6.02 395mm...If a 6.00ID was available I would have got it. Maybe my next barrel




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users