Jump to content


Attn: KWA Staff… Internals


  • Please log in to reply
10 replies to this topic

#1 Gunnie 36

Gunnie 36

    Newbie

  • Members
  • Pip
  • 6 posts

Posted 03 March 2009 - 07:04 PM

Can you spec the internal please …

What is compatible with interchanging form factory to aftermarket?

Use non-linear spring?
Wiring harness gauge?
Motor type with torque?
Hop up?
Bucking?


Thanks in advance….

#2 Spiggy

Spiggy

    Member

  • Members
  • PipPipPipPip
  • 2,136 posts
  • Gender:Male
  • Location:City of Industry
  • Country:

Posted 04 March 2009 - 10:28 AM

I don't think staff can tell you any of that information since it would require opening the gun (and ultimately voiding the warranty.)

View PostGunnie 36, on Mar 3 2009, 07:04 PM, said:

Can you spec the internal please …

What is compatible with interchanging form factory to aftermarket?

Use non-linear spring?
Wiring harness gauge?
Motor type with torque?
Hop up?
Bucking?


Thanks in advance….


#3 Guest_allizard_*

Guest_allizard_*
  • Guests

Posted 04 March 2009 - 03:19 PM

I actually don't understand the question.  Can you rephrase that please?

#4 thesmokingman

thesmokingman

    Enthusiast

  • Members
  • PipPip
  • 32 posts

Posted 04 March 2009 - 03:23 PM

View Postallizard, on Mar 4 2009, 06:19 PM, said:

I actually don't understand the question.  Can you rephrase that please?
I answered this question when the person also asked over at ASR.

technically most of these questions don't require a response but I'll give a quickie answer

check the compatibility list at the top of the forum
nonlinear springs fit, it wouldn't matter if it was or wasn't linear btw
wiring doesn't need replaced but you could use it as large as you can make fit in the body since it never really enters the gearbox. if you just have to upgrade the wiring situation, eliminate the fuse and upgrade from mini tamiya to deans connectors throughout the system
it uses the short-type motor
check the compatibility list for hopup and nozzle ... the stock ones are well above average even for being plastic in construction

Edited by thesmokingman, 04 March 2009 - 03:29 PM.


#5 Guest_allizard_*

Guest_allizard_*
  • Guests

Posted 04 March 2009 - 04:56 PM

I must have a mental block today . lol.. Thanks!

#6 whiterabbit05

whiterabbit05

    Specialist

  • Members
  • PipPipPip
  • 312 posts
  • Gender:Male

Posted 04 March 2009 - 05:00 PM

View Postthesmokingman, on Mar 4 2009, 05:23 PM, said:

it uses the short-type motor

It actually uses the long-type motor.

Edited by whiterabbit05, 04 March 2009 - 05:01 PM.


#7 Gunnie 36

Gunnie 36

    Newbie

  • Members
  • Pip
  • 6 posts

Posted 04 March 2009 - 05:07 PM

View Postwhiterabbit05, on Mar 4 2009, 07:00 PM, said:

It actually uses the long-type motor.


Thank you.....

#8 thesmokingman

thesmokingman

    Enthusiast

  • Members
  • PipPip
  • 32 posts

Posted 04 March 2009 - 05:10 PM

View PostGunnie 36, on Mar 4 2009, 08:07 PM, said:

Thank you.....

v3 gearbox using a long motor?
really?
no not really.
http://store.kwausa....s/aeg/kg36c.jpg

Edited by thesmokingman, 04 March 2009 - 05:13 PM.


#9 whiterabbit05

whiterabbit05

    Specialist

  • Members
  • PipPipPip
  • 312 posts
  • Gender:Male

Posted 04 March 2009 - 05:11 PM

^I thought you were talking about the version 2 GB for the M4/M16.  

If you are asking about the v3, then it should be the short-type motor.

Edit:  I just noticed this is in the G36 section, oops!  I'm too used to being in the M4 section, haha.

Edited by whiterabbit05, 04 March 2009 - 05:13 PM.


#10 thesmokingman

thesmokingman

    Enthusiast

  • Members
  • PipPip
  • 32 posts

Posted 04 March 2009 - 05:14 PM

sorry for being a jerk, bad info is the bane of airsoft

#11 whiterabbit05

whiterabbit05

    Specialist

  • Members
  • PipPipPip
  • 312 posts
  • Gender:Male

Posted 04 March 2009 - 05:22 PM

I didn't even notice you being a "jerk", haha.  So no harm done, I should have paid more attention anyway.

Edited by whiterabbit05, 04 March 2009 - 05:23 PM.





1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users