Jump to content


Which bucking?


  • Please log in to reply
10 replies to this topic

#1 Animalmother

Animalmother

    Enthusiast

  • Members
  • PipPip
  • 33 posts

Posted 03 October 2012 - 08:10 PM

Which hopup bucking for the g36c?
My g2x is worn out. It was never that great my old stock maruis can top the range.
What bucking can i use without compression issues?

#2 badkarmaas

badkarmaas

    Specialist

  • Members
  • PipPipPip
  • 413 posts
  • Gender:Male
  • Location:Tennessee
  • Interests:Playing airsoft, guitar, snakes.
  • Country:

Posted 04 October 2012 - 06:21 AM

G&G greenie or G&P, have good experiences with both.

#3 Guest_Allizard_*

Guest_Allizard_*
  • Guests

Posted 04 October 2012 - 11:22 AM

2G bucking work as intended.  My G36 can shoot 241 feet flat measured with a laser range finder.  Bucking and the hop-up is stock.  I do have a longer inner barrel.  

Now, your issue can be couple things.
1. Your bucking have grease inside.  Common issue.
2. Your Hopup until dial maybe loose and backed down after firing.  This have happened to me so I replaced with a new hop-up unit.

#4 niko_gpsy

niko_gpsy

    What's a Warranty?

  • Super Moderator
  • PipPipPipPip
  • 5,878 posts
  • Gender:Male
  • Location:Atlanta, GA
  • Interests:Keeping those damn squirrels from putting their filthy little paws on my peaches in my backyard. Oh, Yes. It's not just a hobby, its a passion!!
  • Country:

Posted 04 October 2012 - 12:28 PM

View PostAllizard, on 04 October 2012 - 11:22 AM, said:

2G bucking work as intended.  My G36 can shoot 241 feet flat measured with a laser range.  Bucking and the hop-up is stock.  I do have a longer inner barrel.  

Now, your issue can be couple things.
1. Your bucking have grease inside.  Common issue.
2. Your Hopup until dial maybe loose and backed down after firing.  This have happened to me so I replaced with a new hop-up unit.
Were you using a flat or a harder nub with your G36?

#5 Guest_Allizard_*

Guest_Allizard_*
  • Guests

Posted 04 October 2012 - 01:49 PM

View Postniko_gpsy, on 04 October 2012 - 12:28 PM, said:

Were you using a flat or a harder nub with your G36?

Nope... it's stock.

#6 greatwatermelon

greatwatermelon

    I Break GUNS!

  • Members
  • PipPipPipPip
  • 1,078 posts
  • Gender:Male
  • Location:Irvine, CA
  • Country:

Posted 04 October 2012 - 03:22 PM

I've had great results with the green G&G bucking. However, I've seen the 2GX perform better when the hop up, bucking, and barrel is cleaned of any dirt and grease, like Allizard noted.

#7 Animalmother

Animalmother

    Enthusiast

  • Members
  • PipPip
  • 33 posts

Posted 05 October 2012 - 11:27 AM

I had a systema or stock tokyo marui bucking i stuck in. It was quite a tight fit. I had to cut a little bit to get the c clip in.

My gun has all stock internals with exception the lonex POM piston head. It's all cleaned. No silicone lube or packing.

Stock range is around 170'. I see no need to change the barrel. Ill chrono it somehow when i get home.

#8 erinender987

erinender987

    Newbie

  • Members
  • Pip
  • 1 posts
  • Country:

Posted 15 October 2012 - 06:14 AM

I just put a madbull blue bucking into my CA Sportline M-4. It was a tremendous improvement in accuracy. I had to put my home made nub back in. The nub that came with the bucking was so big that the bb drifted up when the unit was dialed all the way back.

I put the same bucking into my KWA. The original setup didn't do anything for the first couple shots when I played in 45 degree weather. The fit was so tight and the bucking stretched so much I had to trim it shorter to snap the clip back on. I'll see this weekend if there's any detriment in accuracy.

I also would love to hear about what exactly the degree means. Does it have specifically to do with what temperature it's intended to be used at or is it something more vague?



cheap printer cartridges

Edited by erinender987, 19 October 2012 - 11:01 AM.


#9 Animalmother

Animalmother

    Enthusiast

  • Members
  • PipPip
  • 33 posts

Posted 17 October 2012 - 02:07 PM

I did pretty much the same thing I also had to shave a little out to fit the C clip. SO far it works good, going to go do a test soon. It's ouncturing the bottom of a coke can with a m120S systema spring so maybe it's getting good compression.

I use green slime for everything in the gearbox. I do wonder how long it lasts though it's kind of gunky and thick.

#10 niko_gpsy

niko_gpsy

    What's a Warranty?

  • Super Moderator
  • PipPipPipPip
  • 5,878 posts
  • Gender:Male
  • Location:Atlanta, GA
  • Interests:Keeping those damn squirrels from putting their filthy little paws on my peaches in my backyard. Oh, Yes. It's not just a hobby, its a passion!!
  • Country:

Posted 18 October 2012 - 11:09 AM

View PostAnimalmother, on 17 October 2012 - 02:07 PM, said:

I did pretty much the same thing I also had to shave a little out to fit the C clip. SO far it works good, going to go do a test soon. It's ouncturing the bottom of a coke can with a m120S systema spring so maybe it's getting good compression.

I use green slime for everything in the gearbox. I do wonder how long it lasts though it's kind of gunky and thick.

I have heard some really good things about green slime but I wonder myself how well it would hold up.

#11 philsaudio

philsaudio

    Enthusiast

  • Members
  • PipPip
  • 277 posts
  • Gender:Male
  • Location:Atlanta
  • Interests:Playing Bass, Grandkids, camping
  • Country:

Posted 19 November 2012 - 08:40 AM

I did some comparing with the KWA pre 2gx hop-up and the SHS aftermarket hop up in the pre2gx G36C.

With stock barrel, bucking and SHS hop up the airseal was lost. I tried SHS hop-up this with a madbull python and Lonex 70 degree and still not good compression. Why? Because I could not get the madbull/lonex into the KWA hop up. It is too tight.

Since the madbull was r-hopped and the nub and rib inside the lonex bucking was removed, I chucked the bucking inside out a barrel in the drill press and sanded some of the thickness out of the inside of the bucking. I was able to squeeze it into the KWA hop up but it was a little long so I had to trim back some to get the c clip back onto the hop up.

Hamsa at Airsoft Atlanta told me the stock KWA bucking is a little thinner than the rest of them which confirms my experience.

Peace




1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users